CHETNA LEARNING SPHERE

CHETNA LEARNING SPHERE

Current Electricity 2

Q- What is Kirchhoff law ? On which concept it is based?

Ans: The algebraic sum of currents meeting at a junction is zero (ΣI = 0). Equivalently, total current entering a junction equals total current leaving it. It is based on the conservation of charge, since charge cannot accumulate at a junction in a steady current.

Q-State Kirchhoff’s Voltage Law (loop rule). On which law is it based? What sign convention is used?

Ans: In any closed loop, the algebraic sum of emfs equals the algebraic sum of potential drops (ΣE = ΣIR), i.e. Σ ΔV = 0 around the loop. It is based on the conservation of energy. Sign convention: a potential drop (moving along the current through a resistor) is taken as −IR. Moving from the negative to the positive terminal of a cell is +E.

Q-Two cells (E₁ = 4 V, r₁ = 1 Ω) and (E₂ = 2 V, r₂ = 1 Ω) are connected in parallel (same polarity) across a 2 Ω resistor. Find the current in each branch using Kirchhoff’s laws.

Ans: Let I₁ and I₂ be the cell currents and I = I₁ + I₂ the current through R.
Loop 1: 4 − I₁(1) − 2I = 0, so I₁ = 4 − 2I
Loop 2: 2 − I₂(1) − 2I = 0, so I₂ = 2 − 2I
Adding: I = 6 − 4I, so I = 1.2 A, I₁ = 1.6 A, I₂ = −0.4 A.
The negative sign means the 2 V cell is being charged by the stronger cell.

Q-What are ohmic and non-ohmic conductors? Give two examples of each.

Ans:

  • Ohmic: conductors that obey Ohm’s law (V ∝ I at constant temperature), so the V–I graph is a straight line through the origin. Examples: metallic wires (copper, nichrome) and carbon resistors.
  • Non-ohmic: conductors whose V–I graph is not linear (resistance depends on V or I). Examples: diode, thermistor, vacuum tube, electrolytes, transistor.

Q- Explain , when series combination of cell are useful for us.

Ans: Total emf = nE and total internal resistance = nr, so
I = nE / (R + nr)
If R ≫ nr, then I ≈ nE/R, so the current is n times that of a single cell. Series is preferred when the external resistance is much greater than the internal resistance (R ≫ r).

Q- Explain , when parallel combination of cell is useful for us.

Ans: Equivalent emf = E and equivalent internal resistance = r/n, so
I = E / (R + r/n)
If R ≪ r/n, then I ≈ nE/r, which is n times that of a single cell. Parallel is preferred when R ≪ r.
For two unlike cells in parallel:
E_eq = (E₁r₂ + E₂r₁)/(r₁ + r₂), and r_eq = r₁r₂/(r₁ + r₂)

Q-Why does the filament of a bulb behave as a non-ohmic conductor, and how does a p-n junction diode differ from an ohmic conductor?
Ans: As current increases, the filament heats up and its resistance rises (positive temperature coefficient). V/I is therefore not constant, and the V–I graph curves. A diode conducts easily in forward bias but negligibly in reverse bias, so its V–I curve is asymmetric and non-linear, unlike the symmetric straight line of an ohmic conductor.

Q-Define specific resistance (resistivity). Write its SI unit and state what it depends on.
Ans: Resistivity is the resistance of a wire of unit length and unit cross-sectional area: ρ = RA/l. Its SI unit is ohm-metre (Ω m). It depends on the nature of the material and its temperature, but not on the length or area of the wire. Its reciprocal is conductivity, σ = 1/ρ (unit: S m⁻¹).

Q-List the factors on which the resistance of a metallic wire depends.
Ans: From R = ρl/A:

Temperature: R increases with temperature for metals

Length (l): R ∝ l

Cross-sectional area (A): R ∝ 1/A, so a thicker wire has less resistance

Nature of the material: through ρ

Q-A wire of resistance R is uniformly stretched to double its length. Find its new resistance and resistivity.
Ans: Volume stays constant, so when l becomes 2l, A becomes A/2.
R′ = ρ(2l)/(A/2) = 4ρl/A = 4R
Resistivity is a material property, so it is unchanged.

Q-How does the resistance of metals, semiconductors and insulators change with temperature?
Ans:

Alloys (manganin, constantan): resistance is almost constant (α very small).

Metals: resistance increases (α positive).

Semiconductors (Si, Ge) and insulators: resistance decreases (α negative), because more charge carriers are released at higher temperature.

Q-Why are manganin and constantan used for making standard resistances and resistance boxes?
Ans: They have high resistivity (so less material is needed) and a very low temperature coefficient of resistance, so their resistance stays nearly constant with temperature change.

Q-Explain the electron gas model. Define drift velocity and relaxation time, and derive v_d.
Ans: In a metal, free electrons move randomly like gas molecules, colliding with positive ions. With no field, the net velocity is zero. When an electric field E is applied, each electron gains acceleration a = −eE/m, and collisions occur on average every τ seconds (the relaxation time, the average time between two successive collisions).

Drift velocity is the average velocity gained by electrons in the direction opposite to the field:
v_d = −eEτ/m
The current is then I = neAv_d.

Q-State the principle of a meter bridge and derive the formula for an unknown resistance.
Ans: The meter bridge is a practical form of the Wheatstone bridge. At the balance (null) point the galvanometer shows zero deflection, so
P/Q = R/S
For a uniform wire of 100 cm, with the null point at length l from the end with resistance R:
X = R(100 − l)/l

Q-Why should the null point be near the middle of the wire? Why are thick copper strips used, and why is the experiment repeated by interchanging R and X?
Ans:

  • Near the middle (about 50 cm), the percentage error in l is minimum and the bridge is most sensitive.
  • Thick copper strips have negligible resistance, so no extra resistance enters the bridge arms.
  • Interchanging R and X and averaging the results eliminates end corrections (errors from the resistance of the connecting ends)

Q-State the principle of a potentiometer. Why is it better than a voltmeter for measuring emf?
Ans: For a wire of uniform cross-section carrying a constant current, the potential drop across any length is directly proportional to that length (V ∝ l). The potential gradient is k = V/L = IR/L.
It is better than a voltmeter because at balance no current is drawn from the cell, so it measures the true emf. A voltmeter draws some current and reads only the terminal voltage. In effect, the potentiometer has infinite resistance at the balance point.

Q-How can two cells’ emfs be compared using a potentiometer?
Ans: Find the null points l₁ and l₂ for the two cells in turn (each connected through a galvanometer and jockey):
E₁/E₂ = l₁/l₂
To increase sensitivity, reduce the potential gradient, for example by increasing the series resistance (rheostat) in the main circuit so the null lengths become longer.

Q-Derive the expression for the internal resistance of a cell using a potentiometer.
Ans: First balance the cell on open circuit (key K open) to get null length l₁, so E ∝ l₁. Then close K with a known resistance R across the cell and get null length l₂, so terminal voltage V ∝ l₂.
Since E = V + Ir and V = IR, we have E/V = (R + r)/R = l₁/l₂.
r = R(l₁ − l₂)/l₂

JOIN OUR PREMIUM CONTENT

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top