CHETNA LEARNING SPHERE

CHETNA LEARNING SPHERE

CURRENT ELECTRICITY

Q-State Ohm’s law. Draw the V–I graph for an ohmic conductor and state what its slope represents.

Ans-Ohm’s law: at constant temperature, the current through a conductor is directly proportional to the potential difference across its ends: V = IR, where R is a constant called resistance. The V–I graph (V on the X-axis, I on the Y-axis) for an ohmic conductor is a straight line through the origin. Its slope is I/V = 1/R (the conductance).

Q-What is resistance? Write its SI unit and the factors on which the resistance of a conductor depends.

Ans-Resistance is the opposition a conductor offers to the flow of current through it. SI unit: ohm (Ω), where 1 Ω = 1 V/A. It depends on the length (R ∝ l), cross-sectional area (R ∝ 1/A), the material, and the temperature.

Q-Distinguish between a conductor and an insulator with two examples of each. What are semiconductors?

Ans-A conductor allows current to flow easily because it has many free electrons: copper, aluminium, silver. An insulator does not allow current to flow easily because it has almost no free electrons: rubber, glass, wood, plastic. Semiconductors (silicon, germanium) have conductivity between the two, and it increases with temperature or doping.

Q-Why is copper used for electric wires, and why are the wires covered with rubber or plastic?

Ans-Copper has very low resistivity, so it carries current with little heat loss, and it is flexible and affordable. The insulating cover of rubber or plastic prevents electric shock and short circuits, because it does not allow current to leak.

Q-Define specific resistance (resistivity). Write its formula and SI unit.

Ans-Specific resistance is the resistance of a conductor of unit length and unit cross-sectional area. From R = ρl/A, ρ = RA/l. SI unit: ohm metre (Ω m). It depends on the material and the temperature, but not on the dimensions of the wire.

Q-What is 1 kWh? Express it in joules. Find the cost of running five 60 W bulbs for 6 hours a day for 30 days, if the rate is ₹7 per unit.

Ans-1 kWh (one unit) is the electrical energy used when a power of 1 kW is used for 1 hour.
1 kWh = 1000 W × 3600 s = 3.6 × 10⁶ J.
Total power = 5 × 60 = 300 W = 0.3 kW.
Energy per day = 0.3 × 6 = 1.8 kWh. For 30 days = 1.8 × 30 = 54 units.
Cost = 54 × 7 = ₹378.

Q-Write three expressions for electric power. A transmission line of resistance 5 Ω carries a current of 10 A. Find the power lost as heat, and explain why power is transmitted at high voltage.

Ans-P = VI = I²R = V²/R.
Power lost in the line = I²R = 10² × 5 = 500 W.
For a given power P = VI, a higher transmission voltage means a smaller current. Since the loss is I²R, a smaller current cuts the heat loss greatly, so power is sent at high voltage and stepped down near the consumer.

Q-Resistors of 2 Ω, 3 Ω and 6 Ω are connected (a) in series and (b) in parallel. Find the equivalent resistance in each case

Ans-(a) Series: R = 2 + 3 + 6 = 11 Ω.
(b) Parallel: 1/R = 1/2 + 1/3 + 1/6 = (3 + 2 + 1)/6 = 1, so R = 1 Ω.

Q-A 4 Ω and a 12 Ω resistor are connected in parallel, and this combination is connected in series with a 5 Ω resistor across a 16 V supply. Find the total current and the current through the 4 Ω resistor.

Ans-Parallel part: R_p = (4 × 12)/(4 + 12) = 48/16 = 3 Ω.
Total resistance = 3 + 5 = 8 Ω.
Total current I = 16/8 = 2 A.
Voltage across the parallel part = 2 × 3 = 6 V.
Current through the 4 Ω resistor = 6/4 = 1.5 A. (The 12 Ω resistor carries 0.5 A, and 1.5 + 0.5 = 2 A.)

Q-What is emf? Distinguish between emf and potential difference.

Ans-emf is the work done by a source (such as a cell) per unit charge in moving the charge around the complete circuit, which is the potential difference between its terminals when no current is drawn.

emfPotential difference
Exists for the source itselfExists between any two points of a circuit
Measured in an open circuitMeasured in a closed circuit
Greater than the terminal potential difference when current flowsTerminal value is less than the emf when current flows, because of the voltage drop across the internal resistance

Q-Find the resistance of a wire of length 2 m and cross-section 0.5 mm², if the specific resistance of the material is 1.6 × 10⁻⁸ Ω m.

Ans-A = 0.5 mm² = 0.5 × 10⁻⁶ m².
R = ρl/A = (1.6 × 10⁻⁸ × 2)/(0.5 × 10⁻⁶) = (3.2 × 10⁻⁸)/(0.5 × 10⁻⁶) = 0.064 Ω.

Q-A wire is stretched to double its length (its volume stays the same). How does its resistance change?

Ans-Volume = lA stays constant. If l doubles, A halves. R = ρl/A, so the new R = ρ(2l)/(A/2) = 4ρl/A. The resistance becomes 4 times the original.

Join Our Premium Content

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top